Common faults and maintenance methods of children’s playground equipment

As time goes by, children’s amusement equipment may fail due to equipment wear or human factors. If the children’s amusement equipment is not properly repaired and maintained, it will cause major problems with the children’s amusement equipment. Today we will share and discuss common failures and maintenance issues of children’s amusement equipment. 1. Common failures of children’s amusement equipment (I) Failure of the oil pump of children’s amusement equipment 1. The oil pump cannot absorb oil: first check the oil pump filter to see if there is any dirt accumulation. If there is, the oil filter should be disassembled and cleaned in time to remove the dirt. If the oil is too dirty, replace it with new oil; if there is insufficient oil in the tank, add enough oil to the tank. 2. Oil pump leakage: check whether the sealing ring is intact. If the seal is not good, it can be replaced. (II) Children’s amusement equipment cannot start normally 1. Check whether the circuit and voltage are normal. If the circuit is normal, check whether the instantaneous voltage at startup is normal. If the instantaneous voltage at startup is too low, consider whether it is necessary to increase the...

Learn More >>

Cleaning techniques and maintenance methods for children’s playground equipment in amusement parks

Children’s health is not only a concern for parents, teachers, and the education system, but also requires sufficient attention to the physical and mental health of children in amusement parks. The related amusement facilities in children’s amusement parks not only need to ensure the physical health of children through cleanliness, but also ensure the physical and mental development of children in terms of exercising their sports ability, physical coordination, interaction, collaboration, and even intelligence with other children or parents. Moreover, cleaning and maintenance of children’s amusement equipment are important aspects of daily work in children’s amusement parks. Improper cleaning and maintenance of equipment may affect the effectiveness and service life of children’s amusement equipment. Therefore, these two tasks have become emphasized and valued by many children’s amusement project investors in their management work. Below, we will share specific methods for cleaning and maintaining children’s playground equipment for reference, hoping to be helpful to you. (Zhengzhou Aerospace Amusement’s Self Controlled Dinosaur, a Children’s Amusement Equipment Manufacturer) 1、 Cleaning techniques and methods for children’s playground equipment In the cleaning work of children’s playground equipment, for plastic parts and fiberglass, we can generally dilute them with soap water, 84 disinfectant, bleach, etc., soak...

Learn More >>

Guidelines for the Operation of Disco Carousels in Children’s Amusement Equipment

The summer season is approaching, and after children’s summer vacation, the passenger flow of children’s playground equipment disco wheel will increase significantly. The precautions for the operation of disco turntables in summer children’s play equipment are something that relevant operators need to be familiar with before officially starting work. Today, we will share with you three parts: pre operation, during operation, and after operation, hoping to be helpful to you. Precautions for the operation of children’s playground equipment disco turntable 1: Before starting up and operating 1. On duty operators must undergo strict training and obtain certification before taking up their posts, and must possess proficient business operation skills.2. Clean and hygienic, there should be no debris on the platform. 3. Check for cracks and fragments on the turntable, and repair them promptly if necessary. 4. Check for any deformation, cracking, or other abnormal conditions in the weld seam. 5. Check for looseness and detachment of bolts and other fasteners. 6. Check for broken or exposed wires. 7. Check if the grounding connection is good. 8. Run the machine three times before starting up, and only after confirming that it is normal can it be officially put into operation. 9....

Learn More >>

Precautions for the use and maintenance of buzzers in children’s playground equipment

Buzzer is an electronic buzzer with an integrated structure, powered by DC voltage, and used as a sound emitting device in some children’s amusement equipment products. Buzzers are mainly divided into two types: piezoelectric buzzers and electromagnetic buzzers, and can also be divided into active buzzers and passive buzzers. Note that the “source” here does not refer to the power supply, but to the oscillation source. Buzzers are used in children’s amusement facilities such as Skywalk and The Wizard of Oz. What are the precautions for using and maintaining buzzers in children’s amusement facilities? Let’s take a look at the sharing brought by Aerospace Amusement. 1、 Let’s first take a look at the structure of the buzzer: 1. Piezoelectric buzzer The piezoelectric buzzer is mainly composed of a multi harmonic oscillator, piezoelectric buzzer blades, impedance matching device, resonance box, and housing. 2. Electromagnetic buzzer The electromagnetic buzzer consists of an oscillator, electromagnetic coil, magnet, vibrating diaphragm, and housing. 2、 Let’s take a look at the sound principle of the buzzer: The sound principle of a buzzer is composed of a vibrating device and a resonant device, and the buzzer is divided into passive excitation type and active self-excited type. The...

Learn More >>

Load operation test and parameter testing of children’s playground equipment

The normal load operation test (hereinafter referred to as load test) of children’s play equipment is divided into no-load test, full load test, and partial load test. Some products also specify overload test according to their characteristics. Regarding the load operation test and parameter testing of children’s amusement equipment, let’s take a look at the sharing brought by Aerospace Amusement. 一、 Load operation test 1. Sub item experiment Sub item testing refers to the technical performance testing and safety reliability testing of important devices, components, or systems that can or must be combined with overall operation testing (no-load, full load, partial load, or overload testing) and are directly related to personal safety. Sub item testing should be conducted by the testing personnel of the manufacturing unit according to the design verification test outline. 2. No load test The test personnel shall conduct manual and automatic tests under no-load conditions according to the load test operation guidance document, and the number of tests shall not be less than the requirements specified in the load test operation guidance document. During no-load operation, the product should be in a normal and stable state, without any abnormal vibration, shaking, impact, heating, or abnormal noise....

Learn More >>

The bearing system of children’s amusement equipment for self controlled aircraft

The load-bearing system of self controlled aircraft children’s amusement facilities is an important component of the facilities. What are the technical conditions and requirements for the load-bearing system of self controlled aircraft children’s amusement facilities? According to the new version of the national standard document “GB/T 20306-2017 Terminology for Amusement Facilities”, children’s amusement facilities are defined as “amusement facilities specifically designed for children’s play.” The definition of self controlled aircraft amusement facilities is “amusement facilities in which the passenger part is supported by a rigid support arm, rotates around a central vertical axis, and independently controls the lifting and movement in a similar form.” The new version of the national standard document “GB/T 18163-2020 General Technical Conditions for Self controlled Aircraft Amusement Facilities” states that “there are three common types of self controlled aircraft children’s amusement facilities, namely the self controlled aircraft series, octopus series, and other types of self controlled aircraft. The new version of the national standard document GB/T 18163-2020 General Technical Conditions for Self Controlled Aircraft Amusement Facilities stipulates in Article 5 the following technical requirements for the load-bearing system of self controlled aircraft amusement facilities: 5.3.1 The frame of the passenger device should be made of...

Learn More >>